65 zjw Filtre Pres Besleme Pompaları
Konsollu yatay santrifüj bulamaç pompaları/kauçuk astarlı bulamaç pompaları/R55 bulamaç pompaları/rakor contalı bulamaç pompaları/santrifüj contalı bulamaç pompaları/aşınmaya dayanıklı kauçuk bulamaç pompaları/değiştirilebilir bulamaç pompaları/Kömür yıkama bulamaç pompaları/Kum ve çakıl taşıma çamuru taşıma pompalar/mineraller yüzdürme işleme pompaları/kömür yıkama pompaları/Besleme Pompaları
Naipu® NP-ZJW serisi filtre pres besleme pompası, benzersiz hidrolik tasarım ve kurulum modunu kabul eder.
çark, pompa performans eğrisinin normal pompalardan daha dik olmasını sağlayın,
Filtre pres beslemesi, büyük kapasiteyi gerçekleştirmek için direnç değişikliklerine göre değişir,
düşük basınçlı besleme ve düşük kapasiteli, yüksek basınçlı filtre. Pompa, kömür yıkamada yaygın olarak kullanılmaktadır,
çevre koruma, alüminyum fabrikası, eritme tesisi vb.
İnşaat Çizimi
Besleme pompasının yapı şeması
1.İki fazlı volüt 2.İki fazlı çark
3.Tek fazlı sarmal 4.Arka plaka
5. Yem odası 6. Yerleştirme çalısı
7.Expeller 8.Expeller kapak plakası
9.Dekompresyon gövdesi 10.Tek fazlı çark
11.Kol demiri 12.Şaft kovanı
13.Kapak plakası 14.Demontaj halkası
15.Su tutma plakası 16.Yatak
17.Şaft 18.Rulman ara kovanı
19.Yatak kapağı 20.Çerçeve
21.Bükülmüş boru
NP-ZJW POMPA SEÇİM TABLOSU
NP-ZJW BESLEME POMPASI PERFORMANS PARAMETRELERİ
Ürüne Genel Bakış:
Olası Arızalar ve Çözümler.
Faults
|
Reason
|
Settlement
|
1.Pump fails to discharge any water,The hand of pressure gauge beat violently
|
1.Suction pipe don`t have enough water.
2.Suction pipe blocked or the valve is locked.
|
1. Inject enough water
2.unlock the inlet valve,clear the blocks
3.Exclude the air leakage
|
2.The pump can`t discharge water,the hand of vacuum meter beat heavily.
|
1.The inlet valve is unlocked or silted up.
2.The resistance of suction pipe is too big or silted up.
3.The height of suction is too high.
|
1.Unlock the valve or desilting
2.improve the design of suction pipe or desilt
3.Lower the height of the installation.
|
3.The pump can`t discharge water,pressure gauge shows heavy pressure.
|
1.The resistance of the discharge pipe is too big.
2.The impeller blocked
3.The speed is slow.
|
1.Check and adjust the outlet pipe.
2.Clear the impeller
3. Improve the speed.
|
4.The pump doesn`t rotate
|
The volute is silted up by the blocks.
|
Clear the blocks
|
5.The capacity is not enough
|
1.The blocks of the impeller or the inlet or outlet pipe.
2.The abrasion of the impeller is heavily.
3.The speed is low to normal
4.Pump is installed unreasonably or the leakage of the inlet pipe.
5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.
6.The inlet valve not open enough or blocked
7.The packing seal leaks
|
1.Clear the impeller or pipe.
2.Change the impeller
3.Adjust the speed
4.Install again or stop leaking.
5.Decrease the height of the transport or reduce the resistance.
6.Unlock the inlet valve
7.Compress the packing tightly
|
6.The motor of the pump is overloaded
|
1.The head of the pump exceeds the head of the working condition.
2.Not consider the slurry density when selecting the pump.
3.The packing press tightly
|
1.Turn down the outlet valve,cut the impeller or lower the speed.
2.Select the motor again.
3.Adjust the the screw of the packing gland
|
7.Abnormal sound in the pump, and no water out
|
1.The resistance of the inlet pipe is too big.
2.The height of the suction is too high.
3.Cavitation occurred
4.there is air in the inlet
5.The temperature of the liquid is too high
|
1.Clear the suction pipe and sluice valve.
2.Lower the height of the suction
3.Adjust the water valve and let the pump operate in the defined limits.
4.Block the leakage.
5.Lowering the liquid temperature.
|
8.pump vibrates
|
1.pump cavitate
2.The block of the impeller single vane
3.The no concentricity between the pump shaft and motor shaft
4.Fasteners or foundation loose
|
1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.
2.Clear the impeller
3.Alignment again
4.Fasten the screw,and reinforce the foundation.
|
9.Bearing is overheat
|
1.lock the cooling water
2.lubrication is not good.
3.the lubrication oil is not clear
4.the wrong direction of the thrust bearing.
5.there is something wrong with the bearing.
|
1.Open the cooling water
2.Adjust the oil quantity
3.Clear the shaft,change oil
4.According to the inlet pressure,adjust the direction of the thrust bearing.
5.Change the bearing
|
10.Packing short life
|
The material of packing is not good
|
Change the packing
|
11.pump leak oil
|
1.High oil level
2.The rubber parts invalid
3.Assembly problem
|
1.Lower the oil level
2.Change rubber spares
3.Adjust the assembly
|
12 Pump head leaking
|
1.The rubber parts not press well
|
Assembly again or press tightly
|
SSS:
S1. Bir üretici fabrikası mısınız?
Evet, biz doğrudan üretim fabrikasıyız ve bu alanda 10 yıldan fazla deneyime sahibiz.
Q2.Satacak stok ürünleriniz var mı?
Bazıları stoklarımızda var, ancak diğerleri yok. Bu ürünleri her zaman müşterilerin ihtiyaçlarına göre ürettiğimizden beri.
Q3.Hangi avantajlara sahipsiniz?
A: Biz doğrudan üreticiyiz ve fiyat rekabetçi.
B: Mühendisimiz bu alanda çok deneyimlidir ve size OEM hizmeti verebiliriz.
C: Biz fabrikayız ve zamanında teslimat için üretim programını ayarlayabiliriz.
İletişim detayları:
Shijiazhuang Naipu Pompa Co, Ltd.
Ekle: No.368 Xinshi Kuzey Yolu, Shijiazhuang Yüksek Teknoloji Sanayi Geliştirme Bölgesi, Hebei, Çin, 050091.
Tel:0086-311-897162903
Faks:0086-311-87162902
İrtibat Kişisi: Karen Tan
Skype: karen_naipump